Mantus Marine
Mantus M2 Anchor
M2GV175
руб270.700,00
-
Designed by the Disabled
for the Disabled
-
100% Satisfaction
Guarantee
-
Lowest Cost Shipping
Quoted in Cart
DIGS LIKE NO OTHER - Mantus M2 Anchor is designed to penetrate dense grassy bottoms and set with unparalleled holding power. Expect the Mantus Anchor to set every time the first time! Released in 2019, M2 has similar performance characteristics to the M1, but a more compact profile and can roll over without the need for a roll bar.
Inclusive Adventures is a Mantus Dealer with experience. We switched to a Mantus M1 Anchor on Possibilities II and an M2 on Possibilities 1 after two dragging incidents.
As a nonprofit, when you purchase from us, 100% of proceeds support providing Inclusive Adventures experiences that produce a shift in PERSPECTIVE from vulnerable to capable with participants and the community.
Ships from Houston TX USA. Under <150lb ships Ground. Orders over >150lb ships FedEx Freight typically $205 to $300.
EASY TO STORE Whether you are a long-range cruiser, racing, or going out for a day sail. The Mantus breaks down for easy storage, so you can store one or two as spares without taking up much-needed boat space. A single bolt is used for the construction to facilitate easy disassembly and storage.
BUILT STRONG
- Formed from high-quality steel plate and high-end precision casting.
- ASTM-certified bolts are oversized with a large margin to ensure safety.
- Although the bolt used in the assembly is load-bearing, only a fraction of the load is transmitted to the bolt.
- Stainless Steel anchors feature a 2205 Duplex shank and 316L stainless steel fluke that are finely polished.
- In the carbon steel version, every part of the anchor system is hot-dipped galvanized for corrosion protection. (All shanks are HT ASTM 514 Steel and flukes are mild steel A36 equivalent).
- The nose of the anchor is reinforced to guarantee lifetime longevity.
Generally, our recommendation is to go with the M1 unless it does not fit. Especially muddy bottoms in rivers, lakes, US Intercoastal, etc
M2 is DESIGNED TO FIT boats with bow sprits and bow pulpits that the M1 with a longer shank and rollbar simply won't fit.
After the release of the Mantus M2 Model, we often get the question: which one is better? Both Anchors have an amazing setting and resetting ability and both are excellent choices for a primary anchor, but each has its own small specific advantages. Both anchors roll over well in most bottom conditions and it is rare for a properly weighted anchor to end up upside down, nevertheless,
- M2 has a shorter shank and eliminating the rollbar provides a better fit for boats with bow pulpits with slotted anchor housing and bow sprits.
- M2 anchor is less likely to get plugged up with muddy weeds without the need for the roll bar
- M1 Anchor due to its rollbar is better at rolling over and holds better in really soft, silty, muddy bottoms. M1 Hoop acts like a scoop in the mud, improving holding power.
- M1 hoop might help prevent chain fouling by wrapping in circles around the shank if the shank tip or ears are not embedded in a harder bottom.
LIFETIME WARRANTY. Mantus anchors are covered by a LIFETIME warranty. If at any time you are dissatisfied with our product, please get in touch with us for a replacement or refund. If an anchor becomes damaged we will ship a replacement part – shank, fluke or roll-bar. The galvanized coating on the anchors has a 3-year warranty.
Comment: many customers see 10+ years before needing to regalvanize. Searching, it appears this might cost $150-$400 depending where and when.
RETURN POLICY. We stand by our product and offer a no questions asked return policy if you find that your anchor does not work as advertised. Follow the link below for more information on returns. RETURNS
ANCHOR SIZING GUIDE
Use the following guide to determine what size of anchor to use:
When making sizing recommendations for a working anchor we are generally referring to the needs of a cruising boat spending most of its time on anchor. In doing so we try to envelope high sustained winds (50 kts) and assume poor holding conditions (low viscosity bottoms). Some may think these recommendations to be too conservative, especially when compared to sizing tables from other manufacturers. Companies often make claims of superior anchor efficiency, stating that their small anchor X will outperform a much heavier anchor from their competitors, and often use sizing charts as a marketing tool to that end, recommending anchors and anchor systems that are dangerously undersized for their intended use. Comparing surface area can be a good judge of potential holding capability. Our anchor sizing recommendations are presented in the table below and divided into three categories: Lunch Anchor category is recommended for lighter use, expected winds under 30 knots, working anchor for winds under 50 knots, and finally, storm anchor recommendations are intended for winds above 50 knots. These recommendations are made assuming the worst-case scenario, a poor holding bottom, and thus may seem conservative but we believe are accurate.
DIMENSIONS AND FIT
We HIGHLY recommend from experience to Print an M1 template, Cut it out with scissors, and stick it to a large piece of cardboard to verify fit on your bow.
Refer to Dimension Image and apply the values below.
| M2 MODEL DIMENSIONS (IMPERIAL) INCHES |
|
A |
B |
C |
D |
E |
F |
G |
H |
I |
J |
K |
| 8 lbs |
20 |
12 |
12 |
5 |
6 |
1 |
0 |
14 |
10 |
3 |
3 |
| 13 lbs |
23 |
14 |
14 |
6 |
7 |
1 |
0 |
16 |
11 |
3 |
4 |
| 17 lbs |
26 |
16 |
15 |
7 |
8 |
1 |
0 |
18 |
13 |
3 |
4 |
| 25 lbs |
29 |
18 |
17 |
8 |
9 |
1 |
1 |
20 |
14 |
4 |
5 |
| 35 lbs |
32 |
19 |
19 |
8 |
10 |
2 |
1 |
22 |
16 |
4 |
5 |
| 45 lbs |
35 |
21 |
20 |
9 |
11 |
2 |
1 |
24 |
17 |
4 |
5 |
| 55 lbs |
37 |
23 |
22 |
10 |
11 |
2 |
1 |
26 |
18 |
5 |
6 |
| 65 lbs |
39 |
24 |
23 |
10 |
12 |
2 |
1 |
27 |
19 |
5 |
6 |
| 85 lbs |
43 |
27 |
25 |
11 |
13 |
2 |
1 |
30 |
21 |
5 |
7 |
| 105 lbs |
46 |
28 |
27 |
12 |
14 |
2 |
1 |
31 |
22 |
6 |
7 |
| 125 lbs |
50 |
31 |
29 |
13 |
15 |
2 |
1 |
34 |
24 |
6 |
8 |
| 155 lbs |
52 |
32 |
31 |
14 |
16 |
3 |
1 |
36 |
26 |
7 |
8 |
| 175 lbs |
55 |
34 |
33 |
14 |
17 |
3 |
1 |
38 |
27 |
7 |
9 |
| M2 MODEL DIMENSIONS (METRIC) mm |
|
A |
B |
C |
D |
E |
F |
G |
H |
I |
J |
K |
| 3.6 kg |
516 |
317 |
304 |
135 |
159 |
25 |
9 |
354 |
253 |
65 |
81 |
| 5.9 kg |
591 |
363 |
348 |
155 |
182 |
29 |
10 |
406 |
290 |
74 |
93 |
| 7.7 kg |
656 |
403 |
387 |
172 |
202 |
32 |
12 |
451 |
322 |
82 |
103 |
| 11.4 kg |
731 |
449 |
431 |
191 |
225 |
36 |
13 |
503 |
359 |
92 |
115 |
| 15.9 kg |
806 |
495 |
476 |
211 |
248 |
40 |
14 |
554 |
395 |
101 |
127 |
| 20.5 kg |
882 |
541 |
520 |
231 |
271 |
43 |
16 |
606 |
432 |
111 |
139 |
| 25.0 kg |
947 |
582 |
559 |
248 |
292 |
47 |
17 |
651 |
464 |
119 |
149 |
| 29.5 kg |
994 |
610 |
586 |
260 |
306 |
49 |
18 |
683 |
487 |
125 |
156 |
| 38.6 kg |
1097 |
674 |
647 |
287 |
338 |
54 |
19 |
754 |
538 |
138 |
172 |
| 47.7 kg |
1163 |
714 |
686 |
304 |
358 |
57 |
21 |
799 |
570 |
146 |
183 |
| 56.8 kg |
1266 |
777 |
747 |
331 |
390 |
62 |
22 |
870 |
621 |
159 |
199 |
| 70.5 kg |
1332 |
818 |
785 |
349 |
410 |
66 |
24 |
915 |
653 |
167 |
209 |
| 79.5 kg |
1407 |
864 |
830 |
368 |
433 |
69 |
25 |
966 |
690 |
177 |
221 |
Assembly
Bolts, Washers, and Nuts are provided with every Mantus Anchor. In the event of replacing a lost fastener, please be sure always to use the proper size. Always use locking washers, or nylon lock nuts, and tighten the nut securely.
Click here to download a printable pdf of the assembly instructions
